|
|
Post by redeye on Sept 23, 2005 19:51:19 GMT 7
on a 1:1 car you have a special tools to set up toe and camber. i know you can get a set up table but for me its too expensive. is there any way i set it up accurately with out set up tools??
|
|
|
|
Post by hachiroku on Sept 24, 2005 3:43:43 GMT 7
easiest way really is to just pay a wheel balancing/alignment
type workshop to do it for you.
It should be fairly cheap.
There are quite a few places that can probably do it in 10 - 15 minutes.
I know of a couple in Ubi area.
|
|
|
|
Post by redeye on Sept 24, 2005 7:08:31 GMT 7
loooooooooooooool where did that sentace go???
i was talking about my RC car ;D
i was just wondering if there was any other way to adjust each side the same amount.
any way i found a way just use a cricle cutter ;D
|
|
|
|
Post by haowee on Oct 9, 2005 21:15:32 GMT 7
U can just use a pencil and protractor. ;D
|
|
|
|
Post by haowee on Oct 9, 2005 21:15:48 GMT 7
also need a3 paper.
|
|
|
|
Post by MiVeC on Oct 10, 2005 12:18:08 GMT 7
U can just use a pencil and protractor. ;D u make it sound very easy... |
|
|
|
Post by haowee on Oct 10, 2005 15:21:14 GMT 7
ya. It is really easy. So long as the car is straight can liao. I have been using that method to setup all my cars. can practice your maths at the same time. ;D
|
|
|
|
Post by Champagne Supernova™ on Oct 10, 2005 20:17:24 GMT 7
wah! how many cars you have? ya. It is really easy. So long as the car is straight can liao. I have been using that method to setup all my cars. can practice your maths at the same time. ;D |
|
|
|
Post by haowee on Oct 10, 2005 20:34:52 GMT 7
3.
|
|
|
|
Post by ReD_SiLViA on Oct 26, 2005 21:12:40 GMT 7
The cheapest way?  use ur eyes to judge... Otherwise get a camber gauge... cost bout below $20... Toe in/out for that... really gotta use ur eyes to gauge |
|
|
|
Post by Champagne Supernova™ on Oct 27, 2005 20:05:29 GMT 7
ur eyes not camber properly how? LOL!
|
|
|
|
Post by Bryant on Oct 27, 2005 22:23:40 GMT 7
no bro, you need to zero you eyes then can use your eyes camber properly.
lol.
|
|
|
|
Post by Champagne Supernova™ on Oct 27, 2005 22:34:31 GMT 7
lol! ya! that important part i missed out first! lol! ZERO!
|
|
|
|
Post by ReD_SiLViA on Oct 27, 2005 23:45:11 GMT 7
ur eyes not camber properly how? LOL! well... i dun blame thingy-eyed dudes... but seriously its the best judgement u can try n run it a few rounds n from therte slowly adjust no point invest in set up gauge tools cos its costly.... very very costly about 120 for a Integy new set up |
|
|
|
Post by domonizo on Nov 15, 2005 16:50:33 GMT 7
does TT01 have a adjustable camber?
|
|
|
|
Post by Rubbish on Nov 15, 2005 20:45:12 GMT 7
U dun even need those $100+ setup kit. I have a set and suddom used cause troublesome. If u on a tight buget all u need is a piece of paper and a set square.
Draw a few lines pallarel to each other and than draw the degree at both end and u got your toe in and toe out. Than use a compass and a set square to measure the camber. That is all.
Even for most racers we all use eye ball toe in kit to see the toe and a camber kit to measure the camber, a ride height gauge and a droop gauge that is all dun really need to spend those money
|
|
Neova
New Drifter
Posts: 24
|
Post by Neova on Nov 8, 2006 21:20:34 GMT 7
aiya if u wanna know more about camber and toe just go play Gran Turismo 4 lahz
the car inside need to tune camber and toe always de... applicable to real life car and also rc car i had 5 cars and i did it to all 5 of them... trust me the game does teach u how to adjust even tho u dun wanna play looool
|
|
